Buy low price, high quality programmator spi flash dip8 with worldwide shipping on AliExpress.com. أغنية تحميل جديد Aghani.org, EZP2010 high speed USB SPI Programmer support 24 25 93 EEPROM 25 flash bios chip download, EZP2010 high speed USB.

Graphic shell for programming Controller software (Firmware with _wo_keys in the name without USB keyboard support, but with support for multimedia buttons and power management buttons. They are for use in android where the virtual You can put a smart keyboard from the market, for example, and use the normal version (firmware from _wo_cdc to work on android without support for composite devices. Everything works except virtual com port). Inf virtual COM port file for windows To avoid the cursor when clicking at all, (after unpacking) put in / system / usr / idc, and set the right 644. Description Connecting Configuring joystick buttons from Reno. Connection, steering wheel: brown — GND red — + 12V lilac — LIN bus Connection, bus: X5 / 8 and X5 / 10 together — LIN bus, you need to connect a 1K pull-up resistor between the bus and + 12V Connection, steering wheel heater: X5 / 7 and + 12V — winding of heater on relay Normally open relay contacts, one through a fuse 10 15A to + 12V, the second to the element of the heater. You can also put a P-MOSFET with a switching current of at least 10A.

Implemented events (LIN event tab): — volume encoder ENCODER VOL UP, ENCODER VOL DN — press the KEY MUTE volume encoder — encoder up-down ENCODER UP, ENCODER DN — pressing the encoder up and down KEY OK — button left KEY BACKWARD — button right KEY FORWARD — menu button KEY MENU — button nav KEY NAV — button voice KEY VOICE — button heating steering KEY SW HEAT All buttons support both short and long press. Developments: — heating off SW HEAT OFF — heating is on SW HEAT ON Implemented reactions (LIN reaction tab): — turn off the steering wheel light — turn on the steering wheel light — turn off the heated steering wheel — turn on heated steering wheel at 20 ° C — turn on heated steering wheel at 25 ° C — turn on heated steering wheel at 30 ° C — turn on the heated steering wheel at 35 ° C — turn on heated steering wheel at 40 ° C When the checkbox is set, the reaction trigger has a switching effect, i.e. If something was turned off, it turns on and vice versa.

As an example, to control the heated steering wheel, you can create: LIN event, select KEY SW HEAT, long press (to protect against possible short presses), LIN reaction to turn on the steering booster at 30 ° C + trigger. And to indicate the on state of heating by the LED on the leg X6 / 6 (anode to X6 / 6, cathode on mass): On the bottom tab Conclusions for this leg, select Act output 0V, add event LIN SW HEAT ON, reaction Output X6 / 6 Full control Turn ON once add event LIN SW HEAT OFF, reaction Output X6 / 6 Full control Turn off once As an example to turn on the steering light when turning on the dimensions: connect + 12V from dimensions to say X5 / 9 is VIN1 add event Voltage VIN1> 6000mV, reaction LIN backlight turn on add event Voltage VIN1. Connecting the connector on the steering wheel: 1 GND 2 + 12V 3 LIN 4 HORN button 5 HORN button Between + 12V and LIN connect a 1K resistor X5 / 8 and X5 / 10 legs together — LIN bus Implemented events for all buttons (LIN event tab) including the horn button. All buttons support both short and long press.

You can also turn the button illumination on or off. By analogy with the backlight for the steering from AUDI. SPI FLASH programmer for scaler RTD2662 from controller: Software version for controller version 4 and software for the programmer shell Types of SPI FLASH memory are written in the jedec.ini file by analogy with my records. Connection: X6 / 4 — GND X6 / 5 — SDA X6 / 6 — SCL Or in the VGA connector or the connector behind it.

Just left to right in it is SCL-SDA-GND. After programming, you can start the controller to work with the 'Reset RTD2662' button without jamming the power.

Reading the memory W25X040 ~ 80 seconds, writing ~ 40 seconds (depends on the content, since blocks with xFF are skipped). The protection bits in the status register after recording are restored to the state before programming. To reattach to the regular version, simply press the button on the board, turn on the power and launch the configuration software.

DLP-USB1232H based SPI programmer schematics In order to use the DLP-USB1232H device as SPI programmer you have to setup a small circuit (e.g. Bcc flicker fixer free download. On a breadboard). See the schematics for details (you can also for easier printing). What you will need: Quantity Device Footprint Value Comments 1 — —. 1 Breadboard — —.